VOG Forum banner
1 - 20 of 27 Posts

·
Registered
Joined
·
48 Posts
Discussion Starter · #1 ·
I'm looking for some passenger equipment from anyone willing to part with some pegs, maybe a saddle / sissy bar combo. I wish my spare Hammer stuff would fit. 17' HB. Preferably blacked out pegs.
 

·
Registered
Joined
·
50 Posts
I was looking for passenger equipment when I 1st got the bike, I've basically given up. The wife isn't in a hurry and neither am I, plus the prices for these things are excessive around now. By the time we are ready to ride 2 up, I'm sure I'll have bought a touring bike by then.

Good luck!
 

·
Registered
Joined
·
9 Posts
Has anybody attempted or looked into making their own passenger peg brackets before?
 

·
Registered
Joined
·
9 Posts
If you could that would be awesome. I'm going to either attempt to make my own or have a shop make some and measurements would help out a lot.
 

·
Registered
Joined
·
9 Posts
Dvldogg187,

Thank you for the measurements and pictures. I am going to start making templates and see what I can come up with. Hopefully I can make it myself with minimal help besides friends with a welder.
 

·
Registered
Joined
·
9 Posts
So far i have mocked up some mounts made of 5/16 wood for trial fitment. Victory had recently received replied to an email that I sent them about the mounts. This is their reply:

Good afternoon Nick,

Thanks for contacting Victory Motorcycles, regarding your 2016 Vegas.

We no longer have a kit available, however, you are able to order the components separately.

The Peg Mount Kit consisted of the following parts:

5137313-156 SUPT-FOOTPEG,PASS,LH,CHR
5134197-156 SUPT-FOOTPEG,PASS,RH,CHR
7517517 SCREW X2
7710644 RING-RTNG,SPIRAL,EXT,SS X2

You can order the above parts through your nearest Victory Dealer, or from the Victory Website under Parts & Service.

If you require further assistance or help with the website, please contact Customer Relations at 1-877-472-1372

Thank you,

Dave

Parts Resolution Specialist

Technical Parts Rep

Victory Motorcycles

2100 Highway 55

Medina, MN 55340

(877) 472-1372
 
  • Angry
Reactions: 16Highball

·
Registered
Joined
·
1 Posts
Thank you for that investigation. I didn't think I'd be answered if I contacted about the kit. I called my local dealer and gave him part numbers and we walked through piecing it together. It was over $500 for it all. NOPE...But it did give me hope.

If you want black....for above quoted part numbers.

LH: 5137313-521 (Mounting Bracket)
RH: 5134197-521 (Mounting Bracket)

If you have a Highball, I used the Polaris website and searched by motorcycle. I used a 2010 Victory Vegas to get the passenger numbers.


5136035-411 FOOTPEG-MACH,LH,BRU $61.49
5136036-411 FOOTPEG-MACH,RH,BRU $61.49
5412261 PAD-FOOTPEG,REAR $13.49 x 2
7556274 WASHER-FOOTPEG,PIVOT $3.29 x2
7556245 WSHR-FL,8X1.6,ZINC $2.29 x 4
7518142 SCR-HXSOC,M8X25,ZPC $6.29 x 4
5134624-266 SUPT-FTPEG,PASS,LH,MACH,BLK $235.79
5134625-266 SUPT-FTPEG,PASS,RH,MACH,BLK $235.79
7710644 RING-RTNG,SPIRAL,EXT,SS $1.79 x 2
7661980 PIN-PIVOT,FOOTPEG $6.29 x 2
 

·
Registered
Joined
·
724 Posts
What is essential are the left/right mounts which at $61.49 each isn't too bad. Unless you insist on stock pegs, the rest should be not difficult to procure. Total cost maybe a tad over $200?

PS: I guess the above doesn't actually show the price of the mounting brackets.
 
1 - 20 of 27 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top